英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
021161查看　021161　在百度字典中的解释百度英翻中〔查看〕
021161查看　021161　在Google字典中的解释Google英翻中〔查看〕
021161查看　021161　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • 802. 11s best practice (STP needed? same diff channel . . . - OpenWrt Forum
    When using three devices in 802 11s should STP be enabled on any of the devices? If so, on which? Also when using an 80Mhz 802 11s mesh on 5Ghz should the access points be set to the same channel as the mesh or a non-overlapping channel? Here, it suggests to use a different channel for the access point: If this radio device will be used for the mesh traffic, make sure all mesh nodes use the
  • STP doesnt work - Installing and Using OpenWrt - OpenWrt Forum
    Hi there I recently got zbtlink we-1602 device with dual-sim I already have compiled my firmware and installed it in my device fine Everything work just fine, except STP lan1, lan2, lan3 and lan4 are in one bridge (br-lan) STP is on root@OpenWrt:~# brctl show bridge name bridge id STP enabled interfaces br-lan 7fff f85e3c316c24 yes lan4 lan2 lan3 lan1 I plugged one end of patch cord in
  • 10G Router High End? - Page 2 - OpenWrt Forum
    At least to me, a 4-5 port switch which sells solidly in the three-figure-range simply doesn't make any sense (maybe 8 ports, for a tiered VIP segment, but that's the bare minimum to be viable - and I'm not even mumbling about 'managed', yet)
  • WDS network - setting STP right - OpenWrt Forum
    Linksys did just enable STP on the WDS AP So i gave it a try - and it works! So STP is only active on the main router now client1+2+3 have it disabled Can somebody explain me why I have to set it up like that? The wiki describes clearly it has to be activated on the WDS client's lan bridge? I also read that STP only works on the wired side of the network? But this can't be true, right
  • Making managed switch out of unmanaged Zyxel XGS1010-12
    Maybe some of you already know Zyxel XGS10 12 home series multigigabit switches has almost the same hardware across all models: same CPU, ROM, RAM and most of the networking chips And the cheapest unmanaged XGS1010-12 could be flashed to be managed, like XGS1210-12 It could be done very easily, since even console header is accessible without disassembly of the unit and you don't need to
  • OpenWrt Table of Hardware
    Explore the OpenWrt Table of Hardware Find detailed compatibility information for routers, access points, and embedded devices supported by OpenWrt firmware
  • Subnet communication for 10GbE and 1GbE : r HomeNetworking - Reddit
    So I flashed the firmware of my router to OpenWRT to allow more flexibility I can enable ECMP But I need to get the subnets configured correctly first Thanks for your feedback but my goal is to have both working, because 1GbE devices (wifi anything not hooked to the 10GbE switch) will only have one 1 GbE interface to the 10GbE network So there is an obvious bandwidth limit if I do what you
  • OpenWrt Table of Hardware
    Comprehensive list of devices compatible with OpenWrt firmware Find the perfect hardware for your open-source networking project
  • How to connect bridge two subnets within the same router - OpenWrt Forum
    Hi, all, I followed this instruction to connect my desktop computer to wifi Now, my desktop has the IP address "192 168 2 14" while my laptop which connects to the same wifi has an IP address "192 168 1 16" I have some files shared in my desktop running windows 11 But my laptop cannot find those files by visiting "192 168 2 14" How do I connect bridge two subnets within the same router
  • Trying to bridge two subnets on the same interface (no . . . - OpenWrt Forum
    Here's my situation: I have an openwrt installed on the TL-WR1043ND v2 (the wifi is turned off) the router is connected to the 24 port switch with just a single LAN port the WAN port is connected to the internet modem what I also have is tp-link deco, configured in router mode it's also connected to the same switch the main deco unit can be seen in openwrt's dhcp client's list with a LAN
  • Mesh in combination with STP - For Developers - OpenWrt Forum
    What I observe in this setup is that the STP messages (BPDUs) send over the wired interface (eth1 1) are handled correct resulting in the Mesh GWs to have the propper understanding of the STP root However, the Mesh STA do receive the BPDUs over the mesh interface (mesh0) but seem not to act on these messages tcpdump on the Mesh STA does show these messages but the Mesh STA remains convinced
  • Spanning tree protocol on which bridge? : r openwrt - Reddit
    Spanning tree protocol on which bridge? I have two Dumb APs on my network One of the APs has a direct Ethernet to my switch The other one uses WDS to connect to the first one in order to get on the network All network interfaces on both APs are bridged together so there’s no routing done at all
  • Need Help: Proxmox Bridge Setup - Level1Techs Forums
    If I figured this part out correctly, Router ports H0 thru H4 are passed-thru, so OpenWRT sees them as separate hardware ports and can bridge them as desired on the OpenWrt side They are otherwise invisible to proxmox and the switch The data flows at 2 5 Gbe to each router port
  • Change interface br-lan from 100 mb to 1 gigabit. Help me - OpenWrt Forum
    On the previous firmware, I measured the iperf3 in my local network on the same hardware, it was about 900 mbps I can not understand why the speed on the LAN-Wifi bridge is always limited to about 95 mbps, with a connection of 270 Mbit (5Hz) I think that this is a soft limit of 100 Mbps on the inside Switch





中文字典-英文字典  2005-2009